bus bar
英 [bʌs bɑː(r)]
美 [bʌs bɑːr]
导电母线；汇流条
双语例句
- It has been shown that the quality plates formed by tackless formation is strongly linked to the con-tact resistance between the plates and conducting bus bar.
叙述了不焊接化成工艺极板质量的不一致性，其产生的主要原因就化成工艺来说是极板与导电母条的接触电阻的不一致。 - By simplifying the geometry model of the copper bus bar continuous extrusion process, based on a new metal forming simulation package, MSC.
对铜母线连续挤压过程的几何模型进行简化，基于MSC。 - The utility model which is provided with slot-shaped bus bar contact faces has the advantages of low labor intensity, high processing speed, high machining precision, etc.
槽型母线接触面，具有减少劳动强度，加工速度快，加工精度高等优点。 - Bus Bar's current grade, specification of bus bar, heat stability are as follows.
母线的电流等级，导电排规格，动热稳定性能见下表。 - When multi-loop ribbon heaters extend from the same junction box, every bus bar needs an insulation bush to avoid short circuit.
多回路电热带从同一接线盒接出时，各母线都要有绝缘套隔离以防短路。 - Discusses an Aluminum Electrolysis Production Bus Bar Zero Drifting Shallowly the Solution
浅谈铝电解生产母线零点漂移的解决方法 - Application and lectotype of flexible bus bar on electric locomotive
柔性母排在电力机车上的应用与选型 - Bus bar type current transformator
汇流排式电流互感器 - Analysis and Application about the Feasibility of Manual Parallel Switch on 380V Bus Bar
380V母线手动并联切换可行性分析及应用 - Accident Analysis of Full Power Cut of 110 kV ⅰ Bus Bar for a Substation
一起变电所110kVⅠ段母线全停电事故分析 - Analysis of coupled eddy current-thermal field for heavy current bus bar
大电流母排三维涡流场-温度场耦合分析 - During the installation of ribbon heater, when one end of cable was connected to power, another end of bus bar should be sealed with matching head so that two bus bars will not have a short circuit.
电热带安装时，当电缆一端接入电源前应将母线另一端用配套的封头套封好，两条母线不得短路。 - Electromagnetic Field and Fluid Field Calculation and Analysis About the Loss and Heat of GIS Bus Bar
GIS母线损耗发热状况的电磁场与流场计算分析 - Calculation of Loss and Heat of GIS Bus Bar Using Electromagnetic Field and Fluid Field
用电磁场和流场模型计算GIS母线损耗发热 - The metal clamp is fixed on the bus bar through a bolt B passing through the threaded hole.
金属夹通过穿过螺纹孔的螺栓B固定在母排上。 - Wavelet transform is used here to extract fault information from current travelling waves and to implement bus bar protection.
小波变换作为新的数学分支，在这里用来提取电流行波信号中的故障信息，实现母线行波保护。 - It points out the faults of operating device when working bus bars switches to spare bus bars by analysing existing 6 kv bus bar protective configuration, proposes both correspondent improvement suggestions and switching methods of bus bar protecting when coordinating the bus bars switching.
通过对现行6kV主母线保护配置分析，指出了此保护装置在工作母线倒至备用母线运行时存在的缺陷，并在此基础上提出相应的改进建议以及配合母线倒运时母线保护切换的方法。 - Effect of Isolator Operation on Medium Impedance and Digital Bus Bar Protection Selectivity
操作隔离开关对中阻抗及微机母线保护选择性的影响 - On the base of detailed research, Calibration method of measuring network of bus bar, adapting to itself, is put forward, which improves measuring precision of bus bar.
在深入研究的基础上提出了母线测量网络自适应校准方法，提高了母线测量精度； - Research and application of bus bar charge-protection
母线充电保护研究及其应用 - Distributed middle voltage bus bar protection scheme based CAN bus
基于CAN总线的分布式中低压母线保护方案 - The method has good effort in application, and the insulation of the bus bar has been greatly improved.
该方法经实际应用效果良好，母线绝缘值有很大提高，提出了从根本上解决封闭母线绝缘低的处理对策。 - It offers a new method to calculate the balance of the vertical enclosed bus bar.
这为垂直布置封闭母线的热平衡计算提供了一种新的算法。 - Analysis and investigation are carried out for the temperature of bus bar, a thermal conclusion is got by using VC++ language.
用网格法对导体和外壳的温度场进行了分析研究，并利用VC++进行了编程，得到了高垂直布置封闭母线的温度分布规律； - Among the rest, the line protection principle, the transformer protection principle, the bus bar protection principle and the capacitor protection principle that based on the microprocessor are discussed.
其中，着重对微机线路保护、微机变压器保护、微机母线保护和微机电容器保护原理进行了论述。 - In excitation system, bus bar and disconnect switch are two types of basic devices.
在励磁系统中，母线排和隔离开关是最基本的两类器件，直接影响系统的可靠性。 - This paper, based on the partial element equivalent circuit ( PEEC), analysis the power converter of bus bar row, extract the parasitic inductance and parasitic resistance, and then bus bar structure is optimized.
本文基于部分元等效电路理论（partialelementequivalentcircuit，PEEC）对功率变换器母线排进行了分析，提取其寄生电感和寄生电阻，并对母线排的结构进行了优化设计。 - By reasonably simplifying the geometry model of copper bus bar continuous extrusion and the division of forming zone, the parameters of force and energy were analyzed.
通过对连续挤压几何模型合理简化和分区，对铜母线连续挤压变形过程力能进行了分析。 - Presently, the main technologies of producing copper bus bar are the rolling method and the common extrusion method.
目前，生产铜排的主要方法有轧制法和普通挤压法。